fail to get samba info

[fzoellne-2]

Hi!

I have some serious problems getting my nslu2 to work again.
First I attached an usb stick to a hub that was connected to disk 1
port and the slug became confused. After reboot I could no longer
connect to it.

As my aim was to move from hdd to the usb stick I thought of a good
idea would be to reflash the slug and unslung to the stick.

All worked fine except I got the message fail to get Samba info in the
web interface. I flashed th latest unslug (6.10). I tired to reflash
as posted in some forums but nothing worked.
Latest I tried to replax the original firmware V23R63. But the message
still occurs and it hinders me to setup the device correctly.

Any hints ?

[Mike (mwester)]

Flash the original Linksys firmware, and use the Linksys tools to reset
the device to factory defaults.  The easiest is to use the Linksys Web
GUI to reset to factory defaults.

Mike (mwester)

fzoellne wrote:

> Hi!
>
> I have some serious problems getting my nslu2 to work again.
> First I attached an usb stick to a hub that was connected to disk 1
> port and the slug became confused. After reboot I could no longer
> connect to it.
>
> As my aim was to move from hdd to the usb stick I thought of a good
> idea would be to reflash the slug and unslung to the stick.
>
> All worked fine except I got the message fail to get Samba info in the
> web interface. I flashed th latest unslug (6.10). I tired to reflash
> as posted in some forums but nothing worked.
> Latest I tried to replax the original firmware V23R63. But the message
> still occurs and it hinders me to setup the device correctly.
>
> Any hints ?
>
>
>
>
> ------------------------------------
>
> Yahoo! Groups Links
>
>
>
>

[fzoellne-2]

 Hi!

 Did not work. Same message as before after reflashing to orig. firmware.

Frank

>
> 2008/7/14 Mike (mwester) <mwester@...>:
>> Flash the original Linksys firmware, and use the Linksys tools to reset
>> the device to factory defaults. The easiest is to use the Linksys Web
>> GUI to reset to factory defaults.
>>
>> Mike (mwester)
>>
>> fzoellne wrote:
>>> Hi!
>>>
>>> I have some serious problems getting my nslu2 to work again.
>>> First I attached an usb stick to a hub that was connected to disk 1
>>> port and the slug became confused. After reboot I could no longer
>>> connect to it.
>>>
>>> As my aim was to move from hdd to the usb stick I thought of a good
>>> idea would be to reflash the slug and unslung to the stick.
>>>
>>> All worked fine except I got the message fail to get Samba info in the
>>> web interface. I flashed th latest unslug (6.10). I tired to reflash
>>> as posted in some forums but nothing worked.
>>> Latest I tried to replax the original firmware V23R63. But the message
>>> still occurs and it hinders me to setup the device correctly.
>>>
>>> Any hints ?
>>>
>>>
>>>
>>>
>>> ------------------------------------
>>>
>>> Yahoo! Groups Links
>>>
>>>
>>>
>>>
>>
>

[carsten.erley]

Hi,
I had the same problem. Please try to get a new power supply for
testing. That was my solution.

Carsten

--- In nslu2-linux@..., Frank <fzoellne@...> wrote:
>
>  Hi!
>
>  Did not work. Same message as before after reflashing to orig.
firmware.
>
> Frank
> >
> > 2008/7/14 Mike (mwester) <mwester@...>:
> >> Flash the original Linksys firmware, and use the Linksys tools to
reset

> >> the device to factory defaults. The easiest is to use the Linksys Web
> >> GUI to reset to factory defaults.
> >>
> >> Mike (mwester)
> >>
> >> fzoellne wrote:
> >>> Hi!
> >>>
> >>> I have some serious problems getting my nslu2 to work again.
> >>> First I attached an usb stick to a hub that was connected to disk 1
> >>> port and the slug became confused. After reboot I could no longer
> >>> connect to it.
> >>>
> >>> As my aim was to move from hdd to the usb stick I thought of a good
> >>> idea would be to reflash the slug and unslung to the stick.
> >>>
> >>> All worked fine except I got the message fail to get Samba info

in the
> >>> web interface. I flashed th latest unslug (6.10). I tired to reflash
> >>> as posted in some forums but nothing worked.
> >>> Latest I tried to replax the original firmware V23R63. But the
message

> >>> still occurs and it hinders me to setup the device correctly.
> >>>
> >>> Any hints ?
> >>>
> >>>
> >>>
> >>>
> >>> ------------------------------------
> >>>
> >>> Yahoo! Groups Links
> >>>
> >>>
> >>>
> >>>
> >>
> >
>