Pencentra 200?

[Mirco Piccin]

Hi All.
I'm an owner of a Pencentra 200.
Its microprocessor is a 129MHz Toshiba® TX3922 MIPS RISC CPU.

So i've prepared a CF with :
netbsd-GENERIC.gz (renamed an ungzipped)

[ A gzipped NetBSD kernel containing code

 for everything supported in this
 release.  This kernel runs on Vr41xx
 and TX3922 CPUs only.

from : ftp://ftp.netbsd.org/pub/NetBSD/NetBSD-3.1/hpcmips/INSTALL.txt ]
and
pbsdboot.exe

I have no problem to start pbsdboot.exe (using Oencentra 130 framebuffer profile), but i have this error:
"Error: mapping interrupt vector failed".

I know that it's a known problem ( http://article.gmane.org/gmane.os.netbsd.ports.hpcmips/2069/match=pencentra), but is there a solution??

Thanks!

[Mirco Piccin]

Hi all (again).

> Hi All.
> I'm an owner of a Pencentra 200.
> Its microprocessor is a 129MHz Toshiba(R) TX3922 MIPS RISC CPU.
>
> So i've prepared a CF with :
> netbsd-GENERIC.gz (renamed an ungzipped)
> [ A gzipped NetBSD kernel containing code
>
>  for everything supported in this
>  release. This kernel runs on Vr41xx
>  and TX3922 CPUs only.
> from :
> ftp://ftp.netbsd.org/pub/NetBSD/NetBSD-3.1/hpcmips/INSTALL.txt
> ]
> and
> pbsdboot.exe
>
> I have no problem to start pbsdboot.exe (using Oencentra 130 framebuffer
> profile), but i have this error:
> "Error: mapping interrupt vector failed".
>
> I know that it's a known problem (
> http://article.gmane.org/gmane.os.netbsd.ports.hpcmips/2069/match=pencentra),
> but is there a solution??

Anyone has tried the netbsd 4.0 on pencentra 200?
Any tips?

Regards
M

[sainio]

Mirco Piccin wrote:

> Hi all (again).
>
>> Hi All.
>> I'm an owner of a Pencentra 200.
>> Its microprocessor is a 129MHz Toshiba(R) TX3922 MIPS RISC CPU.
>>
>> So i've prepared a CF with :
>> netbsd-GENERIC.gz (renamed an ungzipped)
>> [ A gzipped NetBSD kernel containing code
>>
>>  for everything supported in this
>>  release. This kernel runs on Vr41xx
>>  and TX3922 CPUs only.
>> from :
>> ftp://ftp.netbsd.org/pub/NetBSD/NetBSD-3.1/hpcmips/INSTALL.txt
>> ]
>> and
>> pbsdboot.exe
>>
>> I have no problem to start pbsdboot.exe (using Oencentra 130 framebuffer
>> profile), but i have this error:
>> "Error: mapping interrupt vector failed".
>>
>> I know that it's a known problem (
>>

http://article.gmane.org/gmane.os.netbsd.ports.hpcmips/2069/match=pencentra),
>> but is there a solution??
>
> Anyone has tried the netbsd 4.0 on pencentra 200?
> Any tips?
>
> Regards
> M
Hi Mirco

The GENERIC kernel from 4.0 does not boot, but we have now fixed the problem
in -current compiling with i.e. TX3922, I could send you a kernel
(again :), if you do not like to set up a cross-compilation environment. I
recall, that last time you had problems to boot the kernel I sent you, was
it about the size of the mainmemory??

risto

[Mirco Piccin]

Hi Risto!

>  The GENERIC kernel from 4.0 does not boot, but we have now fixed the problem
>  in -current compiling with i.e. TX3922, I could send you a kernel
>  (again :), if you do not like to set up a cross-compilation environment. I
>  recall, that last time you had problems to boot the kernel I sent you, was
>  it about the size of the mainmemory??

(i remember too!)

My Pencentra 200 has 32 MB of Ram memory.
I'll accept "your" kernel, if you'll send me :-D.
Thanks in advance!

King regards!
M