API CS20 alipm(4) error

[Bryan Vyhmeister-2]

I just installed OpenBSD/alpha 4.1 on the API Networks CS20 Dual 833  
MHz Alpha machine that arrived this week. On the first bootup with  
GENERIC, I had hundreds of errors stating the following:

alipm0: timeout st 0x0

These kept repeating a few hundred times and then something else in  
the boot process would load and then hundreds more. When logged in  
through ssh I don't see the error but I experience pauses of a second  
or so every few seconds. Using UKC to disable alipm(4) corrects the  
problem but I thought it was worth while to point this error out.  
This is also the case with 4.1-stable. The dmesg follows but with  
alipm(4) disabled. The only thing listed in the dmesg with alipm(4)  
enabled is the above error.

Bryan


Unrecognized boot flag '0'.
[ using 548368 bytes of bsd ELF symbol table ]
consinit: not using prom console
Copyright (c) 1982, 1986, 1989, 1991, 1993
        The Regents of the University of California.  All rights reserved.
Copyright (c) 1995-2007 OpenBSD. All rights reserved.  http://
www.OpenBSD.org

OpenBSD 4.1 (GENERIC) #1028: Sun Mar 11 04:03:15 MDT 2007
     deraadt@...:/usr/src/sys/arch/alpha/compile/GENERIC
API CS20D 833 MHz
8192 byte page size, 1 processor.
total memory = 2147483648 (2097152K)
(2924544 reserved for PROM, 2144559104 used by OpenBSD)
avail memory = 1873920000 (1830000K)
using 26178 buffers containing 214450176 bytes (209424K) of memory
mainbus0 (root)
cpu0 at mainbus0: ID 0 (primary), 21264B-4 (unknown minor type 4)
cpu0: Architecture extensions: 307<PAT,MVI,CIX,FIX,BWX>
tsc0 at mainbus0: 21272 Chipset, Cchip rev 0
tsc0: 4 Dchips, 1 memory bus of 32 bytes
tsc0: arrays present: 1024MB, 1024MB, 0MB, 0MB, Dchip 0 rev 1
tsp0 at tsc0
pci0 at tsp0 bus 0
siop0 at pci0 dev 3 function 0 "Symbios Logic 53c1010-66" rev 0x01:  
dec 6600 irq 16, using 8K of on-board RAM
scsibus0 at siop0: 16 targets
sd0 at scsibus0 targ 0 lun 0: <SEAGATE, ST336706LC, 010A> SCSI3 0/
direct fixed
sd0: 35003MB, 26302 cyl, 4 head, 681 sec, 512 bytes/sec, 71687370 sec  
total
fxp0 at pci0 dev 4 function 0 "Intel 8255x" rev 0x08, i82559: dec  
6600 irq 20, address 00:02:56:00:0b:b5
inphy0 at fxp0 phy 1: i82555 10/100 PHY, rev. 4
sio0 at pci0 dev 7 function 0 "Acer Labs M1533 ISA" rev 0xc3
pciide0 at pci0 dev 16 function 0 "Acer Labs M5229 UDMA IDE" rev  
0xc2: DMA, channel 0 configured to compatibility, channel 1  
configured to compatibility
pciide0: channel 0 disabled (no drives)
atapiscsi0 at pciide0 channel 1 drive 0
scsibus1 at atapiscsi0: 2 targets
cd0 at scsibus1 targ 0 lun 0: <SAMSUNG, CD-ROM SN-124, q008> SCSI0 5/
cdrom removable
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
"Acer Labs M7101 Power" rev 0x00 at pci0 dev 17 function 0 not  
configured
isa0 at sio0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
lpt0 at isa0 port 0x3bc/4 irq 7
mcclock0 at isa0 port 0x70/2: mc146818 or compatible
tsp1 at tsc0
pci1 at tsp1 bus 0
fxp1 at pci1 dev 3 function 0 "Intel 8255x" rev 0x08, i82559: dec  
6600 irq 32, address 00:02:56:00:0b:b6
inphy1 at fxp1 phy 1: i82555 10/100 PHY, rev. 4
"Myricom Myrinet LANai 9.2" rev 0x03 at pci1 dev 4 function 0 not  
configured
stray isa irq 15
stray isa irq 3
root on sd0a swap on sd0b
siop0: target 0 now using tagged DT 16 bit 80.0 MHz 62 REQ/ACK offset  
xfers
rootdev=0x800 rrootdev=0x800 rawdev=0x802
stray isa irq 3
Warning: received processor correctable error.
Warning: received processor correctable error.
Warning: received processor correctable error.
Warning: received processor correctable error.
Warning: received processor correctable error.
Warning: received processor correctable error.

[Henning Brauer-10]

* Bryan Vyhmeister <openbsd@...> [2007-05-17 10:05]:
> I just installed OpenBSD/alpha 4.1 on the API Networks CS20 Dual 833  
> MHz Alpha machine that arrived this week. On the first bootup with  
> GENERIC, I had hundreds of errors stating the following:
>
> alipm0: timeout st 0x0

interesting.
works just fine here on (the pretty much identical, guess they only
changed the front bezel)
hp AlphaServer DS20L 833 MHz
and if memory serves theo used as cs20 as well before the ds20

> Warning: received processor correctable error.
> Warning: received processor correctable error.
> Warning: received processor correctable error.
> Warning: received processor correctable error.
> Warning: received processor correctable error.
> Warning: received processor correctable error.

that does not look healthy either. is the hardware just toast?

--
Henning Brauer, hb@..., henning@...
BS Web Services, http://bsws.de
Full-Service ISP - Secure Hosting, Mail and DNS Services
Dedicated Servers, Rootservers, Application Hosting - Hamburg & Amsterdam

[Bryan Vyhmeister-2]

On May 17, 2007, at 4:20 AM, Henning Brauer wrote:

> * Bryan Vyhmeister <openbsd@...> [2007-05-17 10:05]:
>> I just installed OpenBSD/alpha 4.1 on the API Networks CS20 Dual 833
>> MHz Alpha machine that arrived this week. On the first bootup with
>> GENERIC, I had hundreds of errors stating the following:
>>
>> alipm0: timeout st 0x0
>
> interesting.
> works just fine here on (the pretty much identical, guess they only
> changed the front bezel)
> hp AlphaServer DS20L 833 MHz
> and if memory serves theo used as cs20 as well before the ds20

In fact it looks to be the exact same machine shows in:

http://www.openbsd.org/images/newrack.jpg

It is in the left rack about half way down the picture.

>> Warning: received processor correctable error.
>> Warning: received processor correctable error.
>> Warning: received processor correctable error.
>> Warning: received processor correctable error.
>> Warning: received processor correctable error.
>> Warning: received processor correctable error.
>
> that does not look healthy either. is the hardware just toast?

That error only showed up once so far. I think my make build was  
successful. I'll know as soon as I get to the office.

Bryan

[Bryan Vyhmeister-2]

On May 17, 2007, at 4:20 AM, Henning Brauer wrote:

> * Bryan Vyhmeister <openbsd@...> [2007-05-17 10:05]:
>> Warning: received processor correctable error.
>> Warning: received processor correctable error.
>> Warning: received processor correctable error.
>> Warning: received processor correctable error.
>> Warning: received processor correctable error.
>> Warning: received processor correctable error.
>
> that does not look healthy either. is the hardware just toast?

I don't know. My -stable build finished without issue and I am  
building -release right now. So far, so good. That error only showed  
up in that one dmesg that I sent. I had not seen it before or after.  
No signs of it through the whole build last night either.

Bryan